Subs and amps should be matched as closely as possible for best performance and longevity. I have a Pioneer deck, amp, and kicker, installed to shut off from the battery.
The sub cuts on and off at high volume when I use the auxiliary cord to phone. How do I fix this? That could mean your amp cannot handle the sub.
- Video of the Day!
- dating rejection advice.
- relative dating age of fossils.
- tatu dating.
- How To Connect A Subwoofer To A Car Stereo Without An Amp.
- dating order.
Another important factor to consider is Ohms. If you have a 2 ohm sub and a 4 ohm amp it won't produce enough power to properly power the sub. Not Helpful 2 Helpful The wires are not grounded properly, check to make sure the surface is clean, unpainted metal.
Like Bass? Follow Us Facebook
Not Helpful 6 Helpful Not Helpful 5 Helpful What would cause my sub to kick in when radio is on and stop working when I change source to CD? The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna. Remove the wire and find the correct remote amp, then turn on wire or ignition wire to the vehicle.
Not Helpful 15 Helpful You should be able to connect it to the auxiliary on the back of the stereo unit. Not Helpful 3 Helpful 7. My amp is already installed and I just bought a new sub.
Tips for a Subwoofer Installation Without an Amp | It Still Runs
How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on the new sub-box enclosure, there should be another set of RCA plugs or clamps. Just match the positive and negatives. Not Helpful 14 Helpful Remote; connect the REM wire to a fuse that only has power when the car is on.
How to hook up a subwoofer to a stereo system
I cannot turn it up any higher than halfway without my amp going into protective mode. What would cause this? This could be caused by a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 1 Helpful 3. What if I bought my radio harness to fit my truck only?
- Share your voice?
- Powering speaker and a subwoofer without built in amp - Speakers - Audio;
- dating sites better than pof;
- How do you connect a subwoofer to an amplifier? | HowStuffWorks.
Will the wires still match up on the aftermarket radio I purchased? It will just plug into your truck and then connect color coordinated wires. Not Helpful 0 Helpful 1. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car?
- arduino lcd hookup.
- yoshkar-ola dating agency!
- Follow Us on Facebook.
- my fox phoenix my dating place;
- carbon dating fossils accuracy.
Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful Disconnect the negative battery cable from the negative terminal. The negative is the ground for the vehicle's electrical system. Connecting or disconnecting any electrical component with the grounding cable attached to the battery can lead to a short in the vehicle's electrical system.
Remove the fuse from the fuse holder on the amplifier wiring kit's ring terminal. The ring terminal provides the bridge to provide power to the powered subwoofer. Remove the fuse from the fuse holder until the sub is connected to the power supply cable. Replace the fuse as the very last step in the powered subwoofer installation process. The powered subwoofer connects to the stereo more like an amplifier would versus another category of speaker.
Remove the stereo from the vehicle's stereo mounting dock to gain access to the outlets on the rear panel of the stereo.
This is the best way to get more power from your car stereo. Tweet Share Share Share Share. Follow Us on Facebook. Like Us on Facebook.
Picking The Right Subwoofer For Your Car Stereo
If you have recently been to a car wash or have discovered a leak in your roof, chances are there is water got into the rear speakers. Most people that are into music are always into getting more bass. Now installing 6x9s speakers or a separate subwoofer are the options If you are having problems with your JVC car stereo and its displaying a message on screen saying check wiring then reset, the functions