H4 hid hook up

I have a problem with my HID. I installed them myself and they both work but only one of them actually uses the HID light the other other one uses they halogen light that comes with it. Is there anyway you can help me. Thank you for taking your time to read this. Hi Jorge, Do you have the H4 style connector that has the 3 large, flat metal pins coming out of it to plug into your factory wiring? If so I think some of your wires in that connector need to be switched around so it activates the HID instead of the halogen on that one side. Also, try turning on your high beams. Does the problem go away?

That buzzing sound is the high voltage of the ballast arcing somewhere either inside the ballast housing, or where it connects to the bulb. This can be caused by a defective ballast, a bad wire connection, or a defective HID bulb. Really the only way to identify the real problem is to swap parts around. Try swapping your HID ballasts from side to side. What type of sound does the relay make?


  1. Connection Diagram.
  2. HID Installation Guide.
  3. dating emo?
  4. best ipad apps for dating.
  5. speed dating in lansing mi!

I installed an HID kit myself. Got a relay harness with resistors, now they wont work at all, nothing.

HID Installation Guide

Tried reversing the plugs, nothing. It would be the exact same install on your truck. Both my hid lights goes on but when I look at my dash the high beam indicater shows that it is on. I have a honda pilot. Ed, sounds like your relay harness is malfunctioning. Get a good one like what GTR Lighting sells and you should be good to go.

I have a Jeep Compass that the light flicker on and off. Will a can bus hid kit solve this issue or will I have to buy other parts to stop it? Most likely yes, this is the relay harness you need for that vehicle.


  1. Posts navigation!
  2. what to do if your two best friends are dating.
  3. super street fighter 4 matchmaking!
  4. HID Kit Installation Instructions;
  5. New Products.
  6. congruence test dating.
  7. dating site in the philippines.

Select the H11 bulb style option:. I installed hid on my honda pilot and the high beam in my dash stays on. So when I switch to high bean, my high beam flickers. Hi, with the signal power only connecting to one side,the side that is left unconnected, will that not flag a fault up? As in, make the car think you have a bulb out? As my car gives a warning light when there is a bulb out?

HID Lighting System Frequently Asked Questions and Answers | Xenon-Vision HID

Thank you in advance for your help. The answer to your question is, yes for some vehicles. You can do this by either running 2 relay harnesses. Repeat the steps for the second headlight. Note that when installing an HID Kits with a power relay harness, you will only have a single connection going to your factory connector.

Performance Automotive Lighting

The opposite side will remain unplugged which is normal. You may want to weatherproof the empty connector to avoid moisture from damaging it.

Xentec 55 Watt Bi-Xenon HID Installation and Review 5000K

Connect the oval 2-prong plug from the ballast to the Bi-Xenon Relay Harness. Connect the Negative - Terminal to a proper ground. This can connect to your battery or anywhere on your vehicle frame. Repeat for the other side of the relay. Make sure your vehicle is turned off when doing this. The last connection will plug directly to your vehicle. Only one side of your vehicle will need to connect to the Bi-Xenon Relay Harness.


  • HID Lighting System FAQ.
  • radiocarbon dating analysis definition.
  • craig safe dating.
  • Note that when installing your Bi-Xenon Relay Harness, you will only have a single connection going to your factory connector. In this example we will list a package contents of a bulb fitment. The image outlines the connection for one bulb and one controller. The amount of light output is three times that of a standard halogen bulb. The lamps also glow at a higher light temperature closer to natural sunlight that gives it its distinct color and appearance.

    Other companies produce halogen bulbs that are gas-filled. They still have a filament as they are halogen technology, but the gas gives the bulb a bluer color when lit. Xenon-filled halogen bulbs produce little or no more light output than standard halogen bulbs of the same wattage. How long will these bulbs last? They will run for over hours. Our lamp kits and bulbs are made of the finest materials available.

    Could I not just purchase a stronger watt halogen bulb to get a brighter light?

    Single Beam HID Kit Package Contents

    So as you increase the wattage on your bulb you increase the current draw on your entire electrical system. This is critical in motorcycle applications. Motorcycles and automobiles currently use a 12 Volt electrical system for their headlamps. Once lit, they only require 85 volts to keep running.

    Our kits include a power pack that is necessary for the lamps to turn on. The input of the power pack is volts. It is an integral part of the system. We will supply you with all of the necessary components and hardware to install this system into your vehicle. Could I Install the kit myself? For anyone who is mechanically inclined, this installation is considered "do-it-yourself".

    While a typical installation takes approximately an hour, it can vary depending on application conversion or auxiliary. Our kits are ready to install right-out-of-the-box and come complete with everything that you will need. We also provide you a full set of easy-to-read, step-by-step instructions to guide you. With the growing popularity of leasing vehicles, a big concern is whether or not you can bring the vehicle back to its original factory condition.

    Our kits install with little or no modifications to your vehicle.